JET-AM
Self priming shallow well pump is a non-submersible pump that flows fluids by a driving nozzle that transforms the pressure of the fluid into a high-speed jet.
Pump
1.Cast iron pump body
2.Brass impeller
3.AISI 304 shaft
4.Max. liquid temperature: +60℃
5.Max. suction: +9m
Moter
1.Motor with copper winding
2.Built-in thermal protector for single phase motor
3.Insulation class: B
4.Protection class: IP44
5.Max. ambient temperature: +40℃
Application
Transfer clean water or other liquids similar in physical and chemical properties
Well water lifting and garden irrigation
Small living water supply and water sprinkler system
Pressure boosting or supporting equipment
Installation Notice
The shallow well pump should be installed in a dean, dry and ventilated location which provides adequate room for servicing and protection from freezing temperatures. It should be bolted to a good foundation, preferably concrete and provided adequate drainage.
Operation Warning
Do not run the transfer pump without water as the seals and impeller may be permanently damaged. Pouring clean water until pump chamber and the inlet pipe are completely filled.
Model Instruction
Technical Table
Model |
Power |
DN |
Q(m³/h) |
0 |
0.6 |
1.2 |
1.8 |
2.4 |
3 |
3.6 |
4.2 |
4.8 |
5.4 |
6 |
|
kW |
HP |
Q(L/min) |
0 |
10 |
20 |
30 |
40 |
50 |
60 |
70 |
80 |
90 |
100 |
||
JET-370AM |
0.37 |
0.5 |
1"×1" |
H(m) |
34 |
27.7 |
22.5 |
17.5 |
14 |
/ |
/ |
/ |
/ |
/ |
/ |
JET-550AM |
0.55 |
0.75 |
1"×1" |
36 |
32 |
28 |
24.5 |
22 |
20 |
16 |
/ |
/ |
/ |
/ |
|
JET-750AM |
0.75 |
1 |
1"×1" |
42 |
36.7 |
32 |
29 |
27 |
24 |
19 |
/ |
/ |
/ |
/ |
|
JET-920AM |
0.92 |
1.25 |
1"×1" |
48 |
43.5 |
39.5 |
35.8 |
32.5 |
28 |
26 |
/ |
/ |
/ |
/ |
|
JET-1100AM |
1.1 |
1.5 |
1.2"×1" |
48 |
44.5 |
41.5 |
38.5 |
35.5 |
32 |
30 |
26.5 |
23.5 |
20.7 |
18 |
|
JET-1500AM |
1.5 |
2 |
1.2"×1" |
55 |
51 |
47.5 |
44 |
41 |
37.5 |
35 |
31.5 |
28.5 |
25.5 |
23 |
Performance Curve
Model Analysis
NO. |
Component |
Material |
NO. |
Componnet |
Material |
No. |
Component |
Material |
1 |
Drain plug |
Brass |
9 |
Impeller |
PPO/Brass |
17 |
Rotor |
|
2 |
O ring |
NBR |
10 |
O ring |
NBR |
18 |
Sator |
|
3 |
Pump body |
Cast iron |
11 |
Mechanical seal |
Ceramic-graphite |
19 |
Pump base |
ZL102 |
4 |
Nozzle |
PP+GF30 |
12 |
Support |
Cast iron |
20 |
Support |
|
5 |
Ejector tube |
PP+GF30 |
13 |
Capacitor cover |
ABS |
21 |
Rear cover |
ZL102 |
6 |
Diffuser |
PPO+AISI304 |
14 |
Capacitor |
|
22 |
Fan |
PP |
7 |
Nut |
AISI201 |
15 |
Water throwing ring |
NBR |
23 |
Fan cover |
Iron |
8 |
Flat key |
AISI304 |
16 |
Bearing |
|
|
|
|